Direct-To an airport, tracked to the field

intermediatePremium
✈ Cessna 172 G1000⏱ ~11 minutes📊 9 steps

Set up a Direct-To to San Francisco International, use OBS mode to see what the deviation bar is actually measuring, then fly it - course pointer, deviation bar, and the moving map closing on the field.

Fly this one with Premium

The G1000 checks every knob, softkey and entry as you make it, and tells you when something was accepted but wrong.

Step-by-step: Direct-To an airport, tracked to the field

  1. Press the Direct-To (D→) key to open the waypoint field.

    Direct-To draws a great-circle course from where you are right now to any waypoint, and it takes over from whatever leg the flight plan was flying - that is what pressing the key means. Normal sequencing picks up again past the Direct-To waypoint.

  2. Spell KSFO with the FMS knobs and press ENT to activate the Direct-To.

    KSFO is not one of the idents this trainer carries built in - it is read out of the airport database, the way any US field is. Watch the HSI as it activates: the course pointer swings onto the direct track by itself, the box beside it reads DTK, and the deviation bar appears, centred. With GPS as the source the unit sets the course; you do not. This trainer also puts the HSI on GPS for you when you activate a Direct-To; the real G1000 leaves the navigation source where you left it, so on the aircraft check the CDI softkey reads GPS before you trust the needle.

  3. Press the OBS softkey to take the course over.

    OBS mode keeps KSFO as the waypoint you are navigating to but stops the unit choosing the course to it - that is now the CRS knob’s job, the way it is on a VOR. It only works on GPS with a waypoint active, which is why the key was greyed until the Direct-To went in. On a flight plan it also stops the unit sequencing on to the next waypoint, which matters two steps from now.

  4. Turn the CRS knob at least 5° either way and watch the deviation bar slide off centre.

    That is the whole of what a CDI measures: where the course pointer is set against where the waypoint actually lies. Move the pointer and the bar moves, with the aeroplane exactly where it was. So a bar off to one side never tells you on its own that you have drifted - it tells you that you are not on the course that is set.

  5. Push the CRS knob to put the course back onto the bearing to KSFO.

    In OBS mode the push sets the selected course to the bearing from where you are now to the waypoint. It is the quick way back to a centred bar. This trainer re-centres the same way with OBS off, but Garmin’s guide only describes the push for OBS mode and for a VOR. With OBS off on the aircraft, the documented way back is D→, ENT, ENT, which reselects the direct course from where you are.

  6. Press the OBS softkey again to hand the course back to the unit.

    Out of OBS mode the unit carries on along the course you left set - here, the one you just re-centred - and on a flight plan it goes back to stepping from waypoint to waypoint by itself. OBS left on by mistake is a common reason a GPS flight plan seems to stop advancing, so turning it off is part of the procedure, not tidying up.

  7. Set the heading bug to that same course, then engage the autopilot in HDG.

    Heading Select captures and tracks the selected heading. Altitude hold is already engaged, so the aeroplane turns onto the course and stays at 4,500 ft while it does.

  8. Select the MFD and leave it on the map page.

    The dashed magenta line runs from own-ship to KSFO. Once you are established it points straight up the screen - which is the picture the deviation bar has been telling you about in numbers.

  9. Track it in. This finishes when KSFO is inside 5 NM.

    A Direct-To set up properly needs no further input. Keep half an eye on the bar: if it walks off centre the aeroplane is drifting off the line - the line has not moved.

Background reading

← Back to all scenarios